Features: The KENCO Oil Supply Tank & Stand System is designed to supply lube oil to the crank case of a compressor or engine in an isolated location where daily supervision and maintenance are an impossibility. KENCO Oil Supply Tank & Stand Systems used in conjunction with our oil level controllers with low level switches can provide 24 hour protection from lubrication failure. Oil Supply Tanks are available in 5, 16, 30 and 55 gallon capacities.

16G-36 = 16 Gallon Tank with 36″ Stand
16G-56 = 16 Gallon Tank with 56″ Stand
16G-72 = 16 Gallon Tank with 72″ Stand
36S-16 = 36″ Stand for 16 Gallon Tank
56S-16 = 56″ Stand for 16 Gallon Tank
72S-16 = 72″ Stand for 16 Gallon Tank

Features: The Spin-Clean is Fluid Power Energy’s Lube Oil Cleaning Centrifuge which reduces engine wear and extends oil drain intervals. Cleaning the oil used in combustion processes is essential for protecting and extending engine life. The preservation of our environment is an important objective as well, and the Spin-Clean Centrifuge is today’s most effective solution for both.

True Centrifuge
Reduces Hazardous Waste
Reduces Engine Wear
Extends Oil & Filter Life
Removes Solids Below One Micron
Diagnostic Tool
User Friendly
Easy Installation
Rugged Construction

Features: The Kenco Low Flow Meter provides an accurate record of the amount of lubricating oil required to
maintain a constant oil level in the crankcase of an engine or compressor. The Kenco Low Flow Meter is a positive displacement double action, single piston meter. The piston strokes and actuates a mechanical counter that registers the amount of oil flowing through the meter. Each piston stroke equals and registers 0.01 gallon of flow. There are two models available. The model 1618 with a mechanical counter only and the model 14308 with a mechanical counter and a reed switch.

• Flow Rate Range: 0.05 to 5 gallons per hour
• Working Pressure Range: 4.6 to 50 psig
• Mechanical Counter Range: 9999.99 gallons
• Mechanical Counter Resolution: 0.01 gallon

Features: The Kenco Proximity Switch provides a switch signal used to detect the absence of flow in a continuously operating compressor lubrication system by monitoring cyclic movement of the divider valve piston.

CSA NRTL/C Certified for Class I, Groups A, B, C, and D; Class II, Groups E, F, and G; Class III, Enclosure Type 4
• Switch Circuitry: S.P.S.T. (Normally Open)
• Maximum Switch Current: 0.5 Amps AC/DC
• Maximum Switch Voltage: 200 Volts AC/DC
• Maximum Switch Power: 10 Watts DC
• Maximum Temperature: 221° F

Features: KENCO Oil Level Controllers are designed to maintain the running oil level in the crankcase of stationary engines, compressors, and mechanical lubricator boxes. The KENCO oil controller works in conjunction with an overhead oil supply system which feeds the oil level controller. As the oil is consumed, the oil controller supplies the required amount of oil to maintain a proper level in the crankcase. The oil controller maintains the proper amount of oil in the crankcase using a float controlled valve. The valve opens and closes as oil is needed in the crankcase to provide a constant oil level.

Reduces maintenance by maintaining a constant lube level.
Protects against lubrication failure
Controller mechanism fully removable without draining oil
Easy view convex sight window
High pressure applications up to 70psi
Fire Safe Valves Available
Oil inlet allows for piping configuration from any direction
Oil outlets on either side of housing and in the bottom to allow for various piping configurations
Easy access to switch float through 3/8″ vent hole in top of housing for simple testing of switch operation
Direct mount adapters eliminate equalizing problems and reduce installation costs
Models available with multiple switches to measure high and low levels or low/low levels (See KHL, KSHL, KSLL)
Oil level controllers for synthetic oil applications now available
CSA & ATEX Approved explosion proof switch enclosure